WebSite 
RFID Module
  • JMY501
    • JMY501
    • The module and antenna are separate design. 4 wires are linked the antenna and module. Normally the wire should be less than 200mm. The interface is UART & IIC. The module supports series IC cards according to ISO14443A, ISO14443B, ISO15693 and the MIFARE series. And also it supports auto detecting card.
    • JMY501
      More
  • JMY504
    • JMY504
    • JMY504 series are the high performance and low cost RFID Module. And the module and antenna are separate design. 4 wires are linked the antenna and module. Normally the wire should be less than 200mm. The interface is UART & IIC. The module supports series IC cards according to ISO14443A, ISO14443B and the MIFARE series. And also it supports auto detecting card.
    • JMY504
      More
  • JMY505
    • JMY505
    • The module and antenna are separate design. 50ohm coaxial line are linked the antenna and module. Normally the wire should be between 60cm and 100cm; the Max. 10m. The interface is UART & IIC. The module supports series IC cards according to ISO14443A, ISO14443B, ISO15693 and the MIFARE series. And also it supports auto detecting card.
    • JMY505
      More
  • JMY506
    • JMY506
    • The module and antenna are separate design. 50ohm coaxial line are linked the antenna and module. Normally the wire should be between 60cm and 100cm; the Max. 10m. The interface is UART & IIC. The module supports series IC cards according to ISO14443A, ISO14443B and the MIFARE series. And also it supports auto detecting card.
    • JMY506
      More
  • JMY601
    • JMY601
    • The EMC of the module (with four layers PCB) is excellent. The interface is UART (RS232 in TTL level). The module supports series IC cards according to ISO14443A, ISO14443B, ISO15693 and the MIFARE series. And also it supports auto detecting card. The JMY601 series support fully all kinds of contactless IC cards.
    • JMY601
      More
  • JMY602
    • JMY602
    • The module and antenna are integrated design. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. The interface is IIC, UART, RS232 and USB. The module supports series IC cards according to ISO14443A, ISO14443B, ISO15693 and ISO7816(T=0 & T=1).
    • JMY602
      More
  • JMY603
    • JMY603
    • The interface is UART(RS232 level). The module supports series CPU cards according to ISO14443A, ISO14443B and MIFARE 1K & MIFARE 4K etc. It has already been authenticated by the Bank Card Test Center under ISO10373-6.
    • JMY603
      More
  • JMY604
    • JMY604
    • The interface is UART(RS232 level). The module supports series CPU cards according to ISO14443A, ISO14443B and MIFARE 1K & MIFARE 4K etc. The antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. It has already been authenticated by the Bank Card Test Center under ISO10373-6.
    • JMY604
      More
  • JMY607
    • JMY607
    • The interface is UART & IIC. The module supports series IC cards according to ISO14443A, ISO14443B, ISO15693 and the MIFARE series. And also it supports auto detecting card. The designer combined some frequent used command of RF card. So the operation is simple, but the function is powerful.
    • JMY607
      More
  • JMY608
    • JMY608
    • JMY608 is the module version of MR760R&W. JMY608 is the module with USB interface (HID standard). In the systems of Windows, Linux and other PC systems support USB keyboard, the module imitates the USB keyboard to operate the card data. The module supports series IC cards according to ISO15693. And it can set freely read-only the serial number or the data of the card.
    • JMY608
      More
  • JMY609
    • JMY609
    • JMY609 is the module version of MR761R&W. JMY609 is the module with USB interface (HID standard). The module imitates the USB keyboard to operate the card data. The reader supports series IC cards according to ISO14443A, ISO14443B, ISO15693 and ISO7816 (T=0 & T=1). There are 2 SAM card slots in the module.
    • JMY609
      More
  • JMY611
    • JMY611
    • The antenna and module are the split design. And the MCU of JMY611 is MCS51. The module supports series CPU cards according to ISO14443A, ISO14443B and also 20 kinds of cards contain MIFARE 1K. It has already been authenticated by the Bank Card Test Center under ISO10373-6. There are 1 SAM card slot in the reader. JMY611 series support PPSS set.
    • JMY611
      More
  • JMY612
    • JMY612
    • 50ohm coaxial line is linked the antenna and module. Normally the wire should be about between 60cm and 100cm; Max. 10m. The module supports series CPU cards according to ISO14443A, ISO14443B and also 20 kinds of cards contain MIFARE 1K. There are 4 SAM card slots in the reader. JMY612 series support PPSS set.
    • JMY612
      More
  • JMY620
    • JMY620
    • JMY620 is a rfid module which can R/W IC card via IIC or UART interface. It can support contactless IC cards(T=CL) fully. And to send or receive 256 Bytes APDU commands. Meantime supporting FSDI=8.
    • JMY620
      More
  • JMY622
    • JMY622
    • JMY622 has many kinds of funtions and it can support various contactless IC card under international standards. Designer classified&integrated the operation commands for contactless IC cards. In this situation, the uesr can operate it easily via sending simple commands. The most important features for JMY622 is that it can support contactless IC cards(T=CL) fully.
    • JMY622
      More
  • JMY628
    • JMY628
    • JMY628 is a RFID read/write module with UART, IIC or USB port. JMY628 has various functions and supports multi ISO/IEC standard of contactless card. The RF protocol is complex, but the designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module. The modules build in SAM slot. It could operate contact smart card according to ISO7816.
    • JMY628
      More
  • JMY680
    • JMY680
    • The module and antenna are integrated design. Ferrite materials are used between the module motherboard and antenna. This design applies for the environment which has more metal materials around the reading scope. The interface is UART & IIC and RS232C and USB. The module supports series IC cards according to ISO14443A, ISO14443B , ISO15693 and ISO7816(T=0 & T=1).
    • JMY680
      More
  • JMY6801
    • JMY6801
    • JMY6801 is a RFID read/write module with UART, IIC, RS232C or USB port. JMY6801 has various functions and supports multi ISO/IEC standard of contactless card. The RF protocol is complex. The designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module. The modules build in SAM slot. It could operate contact smart card according to ISO7816.
    • JMY6801
      More